Holiday 2015 Promo15% off all artwork, limited time offer!

Blog Subscription

Enter your email in the box below to receive the latest updates from my blog directly to your inbox.


Newsletter Subscription

Subscribe to my newsletter to receive 4 to 5 emails per year where I highlight important news, available originals, and seasonal specials.

Blog Category: Step-by-steps

How to Mount Paper on Board

Mounting paper on board using Grafix Double Tack Mounting Film can be challenging at first. This mounting film is permanent and accidents can happen, especially if one doesn't practice ahead.

I've being using this method for years and I'm quite comfortable with it. It takes me about 10 or 15 minutes to mount a piece, depending on the size.

Above is my finished artwork "In Between" which I will mount on a 12" x 24" x 3/4" thick Ampersand Claybord. At this point my piece measures 12.5" x 24.5", half an inch larger than the board, to account for possible misalignment during mounting. I've already trimmed the white paper edge that I normally leave around the drawing.

This is the back of my artwork which I wiped with a clean cotton rag to make sure there are no pencil debris left on the paper. I always use tracing paper to protect my piece from the cutting board.

Grafix Double Tack Mounting Film is acid free and archival. It has a coat of permanent adhesive on both sides of a thin film, sandwiched between two heavy release papers.

The image above shows the double tack mounting film which is cut a bit larger than the original artwork. I'm lifting the top release paper to expose part of the tacky area; this will be a section about an inch wide. It's always better to release more paper than necessary and then let it fall back into place up to the area that will need to be exposed.

Here I folded the top release paper back, exposing only an inch of the tacky film.

After placing my artwork over the double tack mounting sheet, I made sure it was centered inside the perimeter. At this point the artwork can still be moved because it's not making contact with the tacky film.

A close-up of the artwork positioned over the fold.

With a protective sheet of tracing paper over the artwork, I pressed down on the left side to make contact with the exposed tacky sheet. I then secured it onto the cutting board with tape.

Afterwards I lifted the right side of the artwork and slowly began pulling the release paper from underneath. At the same time, with my other hand, I rubbed the surface with a rag, moving back and forth from one side to the other, until all the release paper is out.

At this point I trimmed the edges of the double tack sheet (and tracing paper) with a sharp X-Acto knife.

I turned over the artwork and placed it face down on the cutting board, using the waxy release paper I just pulled from the tacky sheet as a protection layer. Then I rolled a rubber brayer all over the surface to reinforce the adhesion.

Here's my 12" x 24" Ampersand Claybord. I cleaned the surface with a rag and lightly sanded the sides with extra-fine sandpaper.

To pull out the other release paper from the back of the artwork I used the same method as before, exposing a 1.5" area of the tacky sheet.

Then I placed the Claybord over the mounting sheet and centered it. Again, I can still re-position it at this point because the board is not making contact with the tacky film.

Once the board is perfectly centered over my artwork, I pressed down on the left side to make contact with the exposed tacking sheet.

After placing a sheet of tracing paper over the artwork,  I lifted the right side and slowly began pulling the release paper from underneath. At the same time, with my other hand, I rubbed the surface with a rag, moving back and forth from one side to the other, until all the release paper is out.

Here you can see it from the opposite side.

Once the artwork is mounted onto the board, I pressed down first with a rag and then with a rubber brayer.

I turned the Claybord over.

I trimmed the extra with an X-Acto knife.

To achieve perfect cuts I used a fresh blade for each side of the artwork.

Finally I placed the board under heavy books overnight.

My artwork is now ready for varnishing and framing.

This method works well for mounting paper on board, however it doesn't work for canvas - see Canvas and the Icarus board.

This post is an extension of my previous one on Glassless Framing.

Questions and comments are always welcomed and cherished.

Thank you for visiting!

 

“River Pebbles, No. 11”

River Pebbles, No 11

Title: River Pebbles, No. 11

Outline - Cool Zone

The outline was accomplished with Prismacolor Verithin on the cool zone of the Icarus board.

Color Mapping - Warm Zone - Low Temperature

After drawing the outline I proceeded to map the main colors with Neocolor artist crayons on the warm zone of the Icarus board using a low temperature.

For more on color mapping with artist crayons you can view the following videos:

Melting - Warm Zone - High Temperature

With temperature setting at maximum, I melted the artist crayons using clay shapers (also known as color shapers).

For more on melting artist crayons you can view the following videos:

Tools for Melting Artist Crayons

In the picture above you can see the two color shapers I used for melting and the wet sponge for cleaning. For easier cleaning I spray the surface of the wet sponge with a little Simple Green.

Outline - Detail

Color Mapping - Detail

Melting - Detail

Refining - Detail

Refining with Colored Pencil - Medium Temperature

With the temperature set at medium I developed the colors, values and details of the pebbles by layering and blending colored pencils with a variety of tools like tortillions, paper stumps and a Caran d'Ache blender.

Mounted on 2" Thick Clayboard

I finally mounted the canvas on a 2" thick Claybord and painted the sides with acrylic. The artwork is now ready for varnishing.

 

“River Pebbles, No. 9” - Where’s Waldo?

Original Photo Reference

When I look at a reference photo like the one above, the question I always ask myself is: where's Waldo?

Waldo, for an artist like me, is a good composition hidden in the randomness of nature. Even when I'm the one setting up the still life, I try not to interfere in the way pebbles fall into place. I just take many pictures while anticipating the game I will play later on my computer.

Waldo can be elusive at times. I have images taken years ago that never produced a single Waldo. But my ability to "see" is constantly evolving; I know there's a Waldo waiting to be found even in the most hopeless image.

Composition

Meet Waldo! I found him in the center of the image. Now that I have him, I want to show him off but, as you can see, he looks a little drab. Light and color will do magic.

Values

Here's what he looks like in black and white.

Values Adjusted

Much better - Waldo is coming to life. I just lightened the top left quadrant and pushed the overall value contrast.

Colors Adjusted

Now we're talking!

River Pebbles, No. 9

And here is my finished piece - in honor of Waldo of course!

Title: River Pebbles, No. 9

For techniques used in this artwork, please see blog post River Pebbles, No.3 - Melting Artist Crayons

 

“River Pebbles, No. 7”

River Pebbles, No. 7

Title: River Pebbles, No. 7

Outline - Cool Zone

The outline was accomplished with Prismacolor Verithin on the cool zone of the Icarus board.

Color Mapping - Warm Zone - Low Temperature

In this step I blocked-in the main colors on the warm zone with very low heat, just enough to soften the waxy pigments without melting them or blending them.

Burnishing & Blending - Warm Zone - Medium Temperature

After setting the temperature control at medium, I added additional color until there was enough pigment to obliterate the paper. Then I began blending using the point of a tortillon or the side of a paper stump with a very light touch.

Colorless blenders were used to soften edges and details.

 

“Poppy, No. 3”

Poppy, No. 3

Title: Poppy, No. 3

Outline - Cool Zone

The outline is accomplished with Prismacolor Verithin on the cool zone of the Icarus board. I don't like to add too many details at this point, only the principal lines.

Color Mapping - Warm Zone - Low Temperature

I'm blocking-in the main colors of the poppy on the warm zone with very low heat, just enough to soften the waxy pigments without melting them or blending them.

Burnishing & Blending - Warm Zone - Medium Temperature

After setting the temperature control at medium, I add additional color until there's enough pigment to obliterate the paper. Then I begin blending using the point of a  tortillon with a very light touch.

Sometimes I smooth out the color gradations with the side of a paper stump if the area in question is large enough. The very small veins are created with a white Verithin which lifts and lightens the original color underneath.

Burnishing & Blending - Warm Zone - Medium Temperature

Burnishing & Blending - Warm Zone - Medium Temperature

Burnishing & Blending - Warm Zone - Medium Temperature

Refining and Polishing - Warm and Cool Zones

The last step includes refining the edges (cool zone), polishing the color gradations (warm zone), adding the fuzz on the stem (warm zone), filling in the white speckles of paper that are still showing (warm zone), and the signature.

I like to sign my name with a Verithin pencil on the warm zone. I use a lighter color than the background and press enough to create an indentation which is visible even after varnishing.

 

“River Pebbles, No. 4” - Stumps & Tortillions

River Pebbles, No. 4

Title: River Pebbles, No. 4

Color Mapping with Artist Crayons - Cool Zone

After drawing the outline with Verithin colored pencils on the cool zone of the Icarus Drawing Board, I proceeded to map the main colors of the project with Neocolor artist crayons on the cool zone.

For more on color mapping with artist crayons you can view the following videos:

Artist Crayons Melted - High Temperature

With temperature setting at maximum, I melted the artist crayons using a clay shaper (color shaper).

For more on melting artist crayons you can view the following videos:

Orange Pebble Finished in Colored Pencil - Medium Temperature

With the temperature set at medium I developed the colors, values and details of the orange pebble by layering colored pencils and blending them with a tortillion.

Blue Pebbles Finished in Colored Pencil - Medium Temperature

The blue pebbles were accomplished in the same manner as the orange pebble.

Red Pebble Finished in Colored Pencil - Medium Temperature

I finished the drawing by completing the red pebble in the same manner as the other pebbles.

Clean-up, Highlights and Signature

Finally I cleaned up the drawing and emphasized the highlights with a white artist crayon. I like my signature to blend in and I can achieve that by using a sharp, white Verithin on the warm zone. It lightens the colors underneath just enough to make the letters visible without detracting from the art.

Paper Stump and Tortillion

When I first started experimenting with heat I was always on the lookout for different tools that would work with my technique. I remember trying tortillions and disliking them. I found that I couldn't really use them by the long side of the point because they would leave indentations/ridges on the waxy pigments.

The paper stumps that I normally use for large artwork were too thick and soft for this small project. At the same time I was getting very frustrated with how inconsistent the various colorless blenders have been lately. Finally I decided to give the tortillion another try and, guess what? It works great! The point is very thin and sturdy, not as soft as the paper stump's, perfect for blending colored pencils. It's easy to clean with sandpaper and very inexpensive. If you're using it already, you're way ahead of me. If you're not, try one and you'll be pleased!

 

“River Pebbles, No. 3 - Melting Artist Crayons”

Title: River Pebbles, No. 3

Outline - Cool Zone

The outline was accomplished with Verithin Colored Pencils on the cool zone of the Icarus Drawing Board.

Color Mapping with Artist Crayons - Cool Zone

For more on color mapping with artist crayons you can view the following videos:

Detail View of Color Mapping

Here you can see the pigment density needed to achieve complete paper coverage after melting.

Melting Artist Crayons - Warm Zone

With temperature setting at maximum, I begin melting the artist crayons with a clay shaper (or color shaper).

For more on melting artist crayons you can view the following videos:

Melting Completed

Artist crayons save me a lot of time. After they are melted, the paper becomes completely saturated with vibrant colors. The waxy pigments make an ideal substrate for layering colored pencils on top.

Finished Artwork

With temperature setting at medium, I finally layer and blend colored pencils to develop colors, values and details.

You can see a slideshow of this project on the following blog post: Slideshow of "River Pebbles, No. 3".

 

“River Pebbles, No. 2” - A Closer Look

This is a closer look at my second work in a new series of small art depicting some of my favorite subjects.

Title: River Pebbles, No. 2
Size: 5" x 5"
Medium:  Prismacolor Premier Colored Pencil (Verithin and Softcore) and Caran d'Ache Luminance Colored Pencil
Miscellaneous: Lyra Splender Colorless Blender, Gray Paper Stumps
Surface: Stonehenge Paper
Technique: Icarus Drawing Board

River Pebbles, No. 2 is mounted on a 5" x 5" Ampersand Claybord with a 2" cradle. If you are interested in learning how I mount and varnish my artwork, you can read the following post: Glassless Framing.

Outline - Cool Zone

I always use Prismacolor Verithin to draw the outline of my subjects. It's important for me not to add too many details at this point, only the principal lines.

I prefer the back side of Stonehenge paper because it has a little more tooth than the front. That little tooth makes a big difference in how pigments layer, mix and blend, especially on the warm zone. A paper surface that doesn't have much texture is difficult to handle with heat.

Color Mapping - Cool Zone

Color mapping on this paper is a little more time consuming than on a sanded pastel paper. I apply my Prismacolor Softcore and/or Caran d'Ache Luminance with medium pressure on the cool zone until 80-90% of the surface is covered with waxy pigment.

Burnishing and Blending - Warm Zone

Listed below are the main steps I follow to develop the colors and values on the warm zone (high temperature):

  • Burnishing: I saturate the paper with pigment until the white of the paper is completely obliterated (I even burnish white colored pencil over the white areas).
  • Layering: I layer the colors by using the side of the pencil.
  • Blending: when called for, I blend the base and top color together with a paper stump.

Burnishing and Blending - Warm Zone

I continue in the same manner as in the previous step until the whole drawing is completely burnished.

Refining and Polishing - Warm and Cool Zones

I'm adding more details to my drawing. I use the warm zone (medium to low temperature) to blend some of those details into the background, the cool zone to refine and polish with a colorless blender.

Refining and Polishing - Warm and Cool Zones

I continue in the same manner as in the previous step until the whole drawing is finished.

I need your feedback:

With my next small artwork I'm planning to start focusing on specific issues.

Do you have any suggestions? Are there any topics relating to my technique and my art that you would like me to address?

For example, Jill asked me to explain how I make my pebbles shine.

I'd love to get your input.

 

“River Pebbles, No. 2”

River Pebbles, No. 2

This is the second work in a new series of small art depicting some of my favorite subjects. The purpose of this series is to produce more regularly while also working on large pieces. Working small allows me to be more experimental with the Icarus Drawing Board. With each artwork I plan to share something interesting about how I made it.

Title: River Pebbles, No. 2
Size: 5" x 5"
Medium:  Prismacolor Premier Colored Pencil (Verithin and Softcore) and Caran d'Ache Luminance Colored Pencil
Miscellaneous: Lyra Splender Colorless Blender, Gray Paper Stumps
Surface: Stonehenge Paper
Technique: Icarus Drawing Board

My Set-up

Here you can see my set-up. I like to have everything close-by; the pencil tray sits on top of my Icarus board together with the Swifter Duster and the cotton towel. Taping the paper to the glass can be very helpful especially when burnishing on the warm zone.

My TimerMy Sharpeners

 

This yellow timer above is my constant companion. It helps me be more productive and more aware of interruptions. Once I got used to it, starting it and stopping it have become second nature.

To the right of my drawing board I keep two sharpeners: the X-Acto School Pro is electrical and works well with different diameter pencils; the Derwent is battery operated and, even though is made for pencils, I've used it to sharpen crayons for many months with no ill effects. The two sharpeners sit inside an acrylic photo frame together with a thick, moist sponge where I clean my pencils after I sharpen them.

The video above is a slide show of River Pebbles, No. 2. Please come back for my next blog post: River Pebbles, No. 2 - A Closer Look, where I will show you a detailed step-by-step of the project.